Glue for granite two-component granit. Frost-resistant glue for granite for outdoor work: what better
Ideal for facing surfaces of complex bases, such as old tile coatings, heated surfaces, etc.
SPECIFICATIONS:
Work temperature + 5 ... + 30 ° С
The amount of water by 25 kg. Dry mix5.0-5.75 l.
Layer thickness3-10 mm
Consumption when working with a spatula 6x63-4 kg / m?
The viability of the solution is 180 minutes
Tile laying time15 minutes
Tile position adjustment time10 minutes
Time hardening24 hours
Grip strength with a base15 kg / cm? (1MPA)
Hold the weight of the tilene more than 100 kg / m?
Frost resistance less than 35 cycles
Operating temperature --50 to + 70 ° С
Strong circular motions For tile tiles in the glue layer. If the film is formed on adhesives, clean it and apply it again. Length of laying tiles and the ability to adjust the position of the tile depend on the absorbent ability of the substrate and tiles and temperatures ambient. Threads can only be covered after curing glue. There is natural finishing materialBecause it is made of sand and clay. They are easily cleaned and hygienic. They can be located in the bathroom, corridor, kitchen or outdoors - patio, porch, balcony or utility rooms and garage.
Properties:
The tile glue "Unice Granit" has increased strength characteristics, which allows it to be used when laying heavy plates and operate in harsh environments.
High adhesive ability allows you to lead the "top-down" method.
"Unice Granit" is used on heated surfaces (up to + 70 ° C), including in the "Warm floor" system.
The plasticity of the finished solution "Yunis Granit" makes the glue comfortable in the work. After a set of strength, the glue retains its properties with direct contact with water and when exposed to negative temperatures.
"Yunis Granit" is environmentally friendly material. Does not distinguish dangerous to human health and environmental substances in work and operation.
Tile floors are worn and clean, they serve at least 20 years and are suitable for installation in the heating system, because they do not overload the electric current. Tiles offered by manufacturers can be divided into four large groups. These are soft structural tiles for internal work - Walls are laid.
■ Stone tiles are painted, not suitable for socks, resistant to shocks, non-slip, are designed to work both inside and outside. They are durable and therefore used for laying corridors and stairs. The unlawed clay tiles that need to soak, wipe with wax.
Recommended bases:
It is used for non-deformable grounds: concrete (incl. Wcheed concrete and slag concrete), cement (incl. cement plaster), brick, gypsum (GCL, GVL, PGP, etc.), as well as on asphalt.
Performance:
Works should be carried out in dry conditions, at air temperature from +5 to + 30 ° C and relative air humidity not more than 75%.
Currently, the news are metal ceramics and high-quality stainless steel tiles. They are used to lay walls and floors. Sex tiles are slightly thicker compared to wall tile, which means that the walls for the wall can not be laid on the floor. To find out which tile will need for your specific case, read specifications Tiles: wear resistance, frost, sliding.
Tiles are easily combined with other materials: wood, painted surface. In the past, the entire floor was covered with ceilings, but in last years They were laid only in separate areas, such as sink, bath and shower. As the prices for tiles in stores differ, cheaper tiles are combined with more expensive - they put the latter as accent. The price of the tile depends on several factors - material, date of manufacture, quality, etc.
Preparation of the surface:
The base should be smooth, durable, dry, enjoy carrier ability.
Before applying the material, it is necessary to remove the scattering elements, painting coatings, oil and bitumen spots and other contaminants, which prevent the adhesion of the material with the surface.
The base should be aligned horizontally (vertical) with deviations of no more than 1 mm per 1 m length.
For cracking cracks, shells and other small defects in a depth of more than 5mm, it is recommended to use the plasters of the Silin series, "Heat" or "Standard" series depending on the type of surface or operating conditions. For cladding of wet and basement, it is recommended to use the coating waterproofing "hydroplast" as a preparatory layer.
To increase the adhesion strength, the surface is recommended to be treated with a soil "UNIS" in one or two layers, unevenly and highly absorbing bases (gas silicate, foam concrete, etc.) in several layers.
The choice of soil "Unis" is carried out in accordance with the base type.
Wash the base or tile with water before laying is not required.
Thus, such tiles are made on the basis of the mesh, so very suitable for curved and rounded surfaces, as well as to achieve narrow regions. Choosing tiles, do not forget to follow them for many years, so think about whether there will be extravagantly bright color combination will not disappear after a while. You almost never miss if you choose calm tones, natural colors. Keep in mind, is also a tiled room in the apartment in the center of the city or in a wooden wooden house in the village: in the old style of the village carriage, stone tiles or tiles, attributing tiles, will be perfectly combined, and in a modern apartment - bright avant-garde decorations.
Preparation of the solution:
For cooking, only clean capacity and tools should be used.
The dry mixture must be filled into the prepared container with clean water In the proportion of 0.2-0.23 l per 1 kg of a dry mixture and mix until the homogeneous mass is obtained for 3-5 minutes.
Give the solution to stand 3-5 minutes and re-mix. Stirring is made by manual or mechanized methods (professional mixer or drill with a nozzle on small revolutions).
Manual stirring is allowed with a mass of the mixture of a mixture not more than 1 kg. The prepared portion of the solution should be spent over 180 minutes.
When laying a tile, a large room, such as a spacious bathroom, "Play" with flowers, textures, regions. Choose the opposite principle and connect the dark floor with light walls and vice versa - light floors with dark walls. If you prefer compatibility principle, select one-color tiles, only tones of different intensity. Make accents with special decorative tiles, tiles, borders, etc.
When buying tiles, add 5% to the selected amount for cutting and lining. The tile package usually shows the number of shades and sizes. Make sure it is uniform on all packages. Sometimes the tiles that you choose in the store are just an example - you will need to book more and take into account the delivery time.
Attention!
When preparing a solution, it is necessary to observe the recommended ratio "dry mixture-water".
Adding to a dry mixture or a discovered solution of any components, including excess water, leads to a change in the material properties declared by the manufacturer.
Material applying:
The prepared, primed base or work surface with a culma or spatula is applied prepared glue solution 3-10mm thick and smash with a toothed spatula.
For large-format tiles, a spatula with a teeth size of at least 8 mm is used. The weight of the large format tile should not exceed the permissible.
When laying the tile on old tile coatings, to improve the clutch, for the base at a distance of 5x5 cm in checkers, cross-shaped notches are made.
The tile is placed on the glue layer and pressed. The inner surface of the tile should fit tightly to the adhesive solution. When conducting outdoor work, as well as fastening plates from marble, bright limestone, large-format plates, plates with different thickness and relief, the adhesive solution is applied to the operating surface of the plate.
When applying glue on the base, the mortar mixture should be applied to such an area that can be lined with tiles for 15 minutes.
Adjusting the position and cleaning of the surface of the tile from excess glue must be carried out within 10 minutes after laying.
Subsequent grout of seams wall and outdoor tile Color grouts "Unis Color" is allowed 24 hours after cladding.
Operation of the "Warm floor" system is possible not earlier than in 28 days from the date of applying material.
An important factor is the possible deviation of the size due to production technology. If these differences are more than 1, 5 mm, the tiles will be difficult to laminate perfectly. If you put square tiles horizontally, the width of the room will be highlighted if the height of the room will be vertically.
Use tile tiles To connect two different facing plates or to highlight the top edge of the formwork. The network consisting of seams between the plates is optically reduced room. This impression will be reduced if you do not put the tiles entirely, but only to 1, 5-2 m in height.
Recommendations:
In addition to the information on the packaging of information on the use of material when working with it, instructions should be guided by the instructions for conducting general construction and safety in construction.
In the event of doubt, the possibility of applying the bottom material should be referred to as a manufacturer for advice.
Technical description can not replace professional training When performing work.
When planning the work of the tile, you need to know the foundation on which they will be laid - you will choose a tile glue. Chopping plate, which made an old floor-coated floor with smooth, more flexible with tiled glue. If the wall is covered with plasterboard, use adhesive adhesive with special additives or dispersion adhesives. If new tiles are stacked on the old, also choose dispersion adhesives. Synthetic dispersion adhesives are ready to use, but they are dry and relatively expensive.
If you are wound in a wet zone or you are going to install a heating system under floor tiles, use the adhesive adhesive to which the synthetic material is added, which gives glue the elasticity of the tile, making it waterproof. For those places where you have to walk immediately after laying the tile, select Fast Cutting Glue.
STRUCTURE:
Cement, mineral filler, chemical additives.
Packaging and storage:
The dry mixture is supplied in durable kraft bags. Warranty shelf life in intact branded packaging in dry rooms 12 months from the date of manufacture.
Disposal:
Empty packaging to take on secondary processing or together with solidified residues to dispose of as household garbage.
The glue is not recommended for lining of pools, furnaces and fireplaces.
Attention! Take care of children. While working, use gloves. If you get into the eyes, rinse them with water.
Works should be carried out in dry conditions, at air temperature from +5 to + 30 ° C and relative air humidity not more than 75%.
Surface preparationThe base should be smooth, durable, dry, have a bearing capacity. Before applying the material, it is necessary to remove the scattering elements, painting coatings, oil and bitumen spots and other contaminants, which prevent the adhesion of the material with the surface.
The base should be aligned horizontally (vertical) with deviations of no more than 1 mm per 1 m length.
For cracking cracks, shells and other small defects in a depth of more than 5mm, it is recommended to use the plasters of the Silin series, "Heat" or "Standard" series depending on the type of surface or operating conditions. For cladding of wet and basement, it is recommended to use the coating waterproofing "hydroplast" as a preparatory layer.
To increase the adhesion strength, the surface is recommended to be treated with soil "Unis" in one or two layers; Uneven and strongly absorbing bases (gas silicate, foam concrete, etc.) in several layers. The choice of soil "Unis" is carried out in accordance with the base type.
Wash the base or tile with water before laying is not required.
Preparation of solutionFor cooking, only clean capacity and tools should be used.
The dry mixture must be filled into the prepared capacity with clean water in the proportion of 0.2-0.23l per 1 kg of a dry mixture and mix until the homogeneous mass is obtained for 3-5 minutes. Give the solution to stand 3-5 minutes and re-mix. Stirring is made by a mechanized method - a professional mixer with a nozzle on small revolutions. Manual stirring is allowed with a mass of the mixture of a mixture not more than 1 kg. The prepared portion of the solution should be spent over 180 minutes.
Attention!
When preparing a solution, it is necessary to observe the recommended ratio "dry mixture-water". Adding to a dry mixture or a discovered solution of any components, including excess water, leads to a change in the material properties declared by the manufacturer.
Applying materialA prepared adhesive solution is applied to the prepared, primed base or work surface with a cooler or a spatula with a thickness of 3-10mm thick and smoothed by a toothed spatula.
For large-format tiles, a spatula with a teeth size of at least 8mm is used. The weight of the large format tile should not exceed the permissible.
When laying a tile on old tile coatings, to improve the clutch, for the base at a distance of 5x5 cm in checkered procedure, cruciform notches are made.
The tile is placed on the glue layer and pressed. The inner surface of the tile should fit tightly to the adhesive solution. When conducting outdoor work, as well as fastening plates from marble, bright limestone, large-format plates, plates with different thickness and relief, the adhesive solution is applied to the operating surface of the plate.
When applying glue on the base, the mortar mixture should be applied to such an area that can be lined with tiles for 20 minutes.
Adjusting the position and cleaning of the surface of the tile from excess glue must be carried out within 20 minutes after laying.
The subsequent grout of the seams of the wall and floor tile with colored grouts "Unis Color" is allowed 24 hours after cladding.
Operation of the "Warm floor" system is possible not earlier than in 28 days from the date of applying material.
RecommendationsIn addition to the information on the packaging of information on the use of material when working with it, instructions should be guided by the instructions for conducting general construction and safety in construction.
In the event of doubt, the possibility of applying the bottom material should be referred to as a manufacturer for advice.
Technical description cannot replace professional training when performing work.