Plaster consumption per m2. Decorative plaster: material consumption

The foundation mineral materials: concrete, cement and cement-limestone plaster. Gypsum substrates, drywall, solid coated polymer coating surfaces inside chipboard and fibreboard. If the walls are not heated, their surface should be hard, smooth, dry, free of adhesive plaster with basic materials: dirt, grease dust, bitumen residues, mold and other similar contaminants. Weak or slightly rinse marks and old paints should be removed.

Pour the powder into a 5 liter water container and mix thoroughly with an electric mixer until smooth. After five minutes, the mixture must be mixed several times, and then plaster can be used. Each package must be diluted with the same amount of water. In water without water, no water is required.

See separate instructions for more detailed instructions. Conclusions and recommendations for plastering. Plastering works should only be carried out by an experienced and experienced worker. Surfaces to be painted must be protected from prolonged exposure to water, so that they are protected from moisture, so that they do not overlap.

Before starting work, all objects in the plaster area that are not used in the plastering process must be covered and protected from splashing. Tile surfaces are selected taking into account weather conditions, the nature of the substrate and the ability to perform the actual plastering work.

Measure carefully the amount of water required to prepare the mixture. Failure to follow the recommendations can result in a mix of improper consistency and will not lead to the desired pattern. During the plastering and drying of the gypsum, the treated surfaces must be protected from direct sunlight, precipitation and wind.

Low temperatures, high humidity and insufficient air circulation prolong the drying time of the gypsum. After work, tools and hands should be washed under running water, taking into account that it will be much more difficult to remove residues when washing expanded polystyrene.

Surfaces where the plaster unintentionally cools should be cleaned with a damp cloth and hardened plaster using a hand trowel. Once the walls are dirty, it is necessary to protect from exposure to the atmosphere and sunlight, and from rapid drying until the rust starts severely.

It is not recommended to apply uneven texture to exterior walls as large, frayed walls can shrink and split. The gauze is alkaline, so be careful not to get into your eyes or skin. After ingestion, rinse with plenty of water and seek medical attention.

Mixer or mixer mixer. Stainless steel cover or masonry. Smooth stainless steel spatula. Stainless steel spatula with teeth from 8 to 10 mm. The following technical parameters are based on a temperature of 23 ℃ and an air humidity of 50%. Other parameters may vary.

Temperature the environment and substrates when plastering and stretching: from 5 ℃ to 25 ℃. Relative humidity for plastering and stretching: up to 80%. Optimum layer thickness: 3 ÷ 4 mm. Maximum plaster thickness: 15 mm. Ready time for using the plaster: ≤ 1.5 hours.

Period of placement: 12 months from the date of manufacture of the mixture indicated on the package. The cost of the plaster is determined by the flat surface of the substrate, the thickness of the finished layer and the structure given to the surface. To find out the exact cost, it is recommended to test the area of ​​the existing base.

The packages are considered to be inaccessible to children. A mixture of cement with polymers and water repellents. All of the above information is based on the latest technologies and technical knowledge of the use of plaster. It does not replace the technical qualifications of designers and plasterers and does not relieve them of their responsibility to comply with building codes and safety regulations.

Fastening the heat-insulating layer to the wall with heat-insulating adhesive and a finishing layer on a reinforced surface. Pieces of abrasive plaster and other irritants burn. The skirting profile is attached to the bottom of the building wall. Thermal insulation boards. Solid slabs of mineral wool or expanded polystyrene are used for insulation insulation. Thermal insulation. Scratch the surface of the armored fabric with lint-free paper.

Plastic jump. Thermal insulation boards are additionally installed on the wall using plastic crowns. Installation with plastic thimbles. A few days after gluing the thermo-insuliacyllis, knocked-down holes appeared, we brammed plastic jaws and nails.

Corner profiles are applied to the corner of the thermal insulation board. Reinforcement mesh is placed over the welded vertical strip. On a reinforced surface, the pavement is filled with a thin layer and, after it has been torn, is lined with abrasive paper. Substrates must be clean, chip-free and dry.

In adverse weather conditions, such as when it rains or blows wind, the period is extended. Hand plaster: Lightly painted spray surface is removed by coating with histolite and rinsed. Abrasive plaster from the surface: the surface is washed with a dry brush and rinsed with a jet of water under pressure in accordance with the statutory regulations.

The surface of the hardened concrete is thoroughly washed and the dirt is removed. Repairing plaster surfaces: When repairing crevices and damaged placements, note that the mortar used to repair the plaster matches the strength and texture of the plaster. The patches must be well glued and dried before staining, so they must be thoroughly covered with histolite fluid and rinsed. When the plaster areas are large, cover with histolite fluate and rinse the entire surface.

Layers of old mineral paints: Unpacked old paints are cleaned dry or damp. Once turned off, colors damaged by atmospheric factors are sanded, scratched or cured. Then thoroughly rinse the entire surface with water. Carrying old layers of dispersion paint: Completely removed mechanically or suspended and then rinsed with hot water under high pressure in accordance with regulatory requirements.

Carrying old layers of dispersion paint: dirt and a slightly scratching layer are cleaned to the ground with a stream of water under pressure or other special methods in accordance with the regulations. Brick brickwork: The paints are only suitable for frost-resistant outdoor bricks, which, for example, do not contain migratory or colored inserts. sand and clay dunes. Seams should be free of cracks and a secure seal or the like. Remove salts with a dry brush. Roof, window and floor joints must be made in accordance with the provisions of the Union of Sulphate Bricks.

Stone processing: Natural stones must be firm, dry and free of salt. Mud stones are cleaned with a stream of water under pressure in accordance with the statutory rules. The stones are repaired without plastering solution, but with stone materials... The correct areas should be tightly bonded and the fluorosilicate should be adequately coated before painting. Rising humidity: due to the rise in humidity, the paint layer dies for the first time. Long-term effects are achieved by installing horizontal insulation.

It is especially useful in older buildings to establish dry and evaporative zones to lay a gravel filter layer between the base and the ground. Sintered primer surfaces: mechanically clean the surface or cover with histolite and rinse with water. Wet areas are covered with histolite-fluate and rinsed with water.

Concrete: Removal of residual binder as well as bulky layer. Unpainted sandstone masonry: scrub the salts with a dry brush. Carrier layers: Complete layers of enamel paints, dispersed paints or synthetic resin are completely removed. The bearing layers of mineral paints are completely removed mechanically. Varnish coat: Rinse to the ground.

Mousse Dirt Surfaces: The mousse board is brushed, scratched or scratched. Whether it is necessary to choose a priming when evaluating the type and properties of the surface. Pay attention to statutory and power instructions. Salt Foamed Surfaces: Spiked surfaces do not guarantee the longevity of the coating or prevent salt cracking.

Can also be sprayed with non-spray machines. Concrete Wall panels: Roller primer. The top layer is roller-coated through the panels and immediately aligned with the foam rotor in one direction. Stir the paint thoroughly and strain when applying a non-spray. Quartz particles can wear out faster and clog faster.

Costs may be higher depending on the substance and substrate. The exact amount you need is to calculate the coverage of the testing area. Avoid direct sunlight on open and hot surfaces when it is raining, windy, foggy, or humid.